Solenoid Switch - 24V - Pair Replacement 24v solenoid pack for the Vetus Bow and Stern thruster models 95, 110, 125 and 160Kgf. This product may not be returned to the original point of purchase. Plea... More Details

Spare Set Zinc Anode Spare set zinc anode for 220/285 kgf bow thrusters  Product Specifications Dimensions6" L × 5" W × 3" HShipping Weight1 lbCountry of OriginITALYHarmonized Code8479.90.80.00 More Details

Spare Zinc Anode Set f/Bow Thruster Spare set zinc anode for 125/130/160 kgf bow thrusters. Fitted to propeller hub center. Supplied complete with cap head allen screw. Product Specifications Dimensio... More Details

Strainer for Type FTR140 This strainer is for the FTR140 waterstrainers. Product Specifications Dimensions3" L × 3" W × 3" HShipping Weight0.09 lb More Details

Thruster Panel Joystick Thanks to the deluxe design and the high-quality coated aluminum front, this new bow or stern thruster panel will be an asset to your dashboard! The panel can be fitted into a ... More Details

V-CAN 3-Point Y-Hub The CANVHUB is a groundbreaking advancement for V-CAN installations, designed to elevate your hardware mounting and cable management experience, specifically tailored for boat buil... More Details

V-CAN Power Supply  - 12V Input Output Max 5A The CANVPS is set to replace the BPCABCPC, bringing a new level of reliability and protection to your V-CAN installations. This advanced power supply is d... More Details

V-Ring V-Ring for BOW125D Product Specifications Dimensions1" L × 1" W × 1" HShipping Weight0.1 lb More Details

V-Ring V30-A Rubber Features: V30-A Rubber V-Ring Product Specifications Dimensions1" L × 1" W × 1" HShipping Weight0.1 lb More Details

Zinc Anode Set f/Bow Thruster - 25 kgf Bow Thrusters Spare set zinc anode for 25 kgf bow thrusters. Supplied with two stainless steel allen head countersunk set screws. Product Specifications Dimensio... More Details

Zinc Anode Set f/Bow Thruster - 35/55 kgf Bow Thrusters Spare set zinc anode for 35/55 kgf bow thrusters. Supplied with two stainless steel allen head countersunk set screws. Product Specifications Di... More Details

Zinc Anode Set f/Bow Thrusters - 75/80/95 kgf Bow Thrusters Spare set zinc anode for 60/75/80/95 kgf bow thrusters. Supplied with two stainless steel Allen head countersunk set screws. Product Specifi... More Details

A.C.E. Transducer Epoxy The perfect material for any in-hull transducer installation. A.C.E stands for Acoustically Conductive Epoxy. This will ensure the bond between the transducer and the boat hull... More Details

11lb Vertical Fiberglass Composite LPG Cylinder with Type 1 Valve - OPD, DOT, TC Approved This composite propane tank has an internal bladder encased in fiberglass, which allows users to see the gas l... More Details

17lb Vertical Fiberglass Composite LPG Cylinder with Type 1 Valve - OPD, DOT, TC Approved This composite propane tank has an internal bladder encased in fiberglass, which allows users to see the gas l... More Details

22lb Vertical Fiberglass Composite LPG Cylinder with Type 1 Valve - OPD, DOT, TC Approved This composite propane tank has an internal bladder encased in fiberglass, which allows users to see the gas l... More Details

.75" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the con... More Details

.75" Tall Stainless Stud w/#10 x 24 Thread Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and secu... More Details

1.25" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the co... More Details

1.5" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the con... More Details

1.5" Tall Stainless Stud w/#10 x 24 Thread Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and secu... More Details

1.5" Tall Stainless Stud w/1/4" x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All s... More Details

1" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the conso... More Details

1" Tall Stainless Stud w/1/4" x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All stu... More Details

2.5" Tall Stainless Stud w/1/4" x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All s... More Details

2" Tall Stainless Stud w/1/4" x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All stu... More Details

Adhesively Bonded Fastener Kit with AT 8040 Adhesive Kit Contains: (1) Plano Storage Box - 11" x 7.25" x 2.75" (50) AT-5 Tie Mount (White) (1) AT-8040 Adhesive (5) AT-850 Mixing Tip (1) AT-300 Dispens... More Details

Footman's Strap Mount The Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is... More Details

Footman's Strap Mount The Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is... More Details

10:1 Gun Plunger for AT-6030 Adhesive 10 Pack Gun Plunger for AT-6030 Adhesive (sold separately) Product Specifications Dimensions8" L × 5" W × 2" HShipping Weight0.5 lb Accessories SKU 106701 — MFG# ... More Details

AT-13 - 10:1 Gun Plunger f/AT-6030 Adhesive - Single Single Pack gun plunger for AT-6030 Adhesive (sold separately). Product Specifications Dimensions9" L × 4" W × 1" HShipping Weight0.5 lb Accessorie... More Details

AT-3 Small White Nylon Tie Mount - Qty. 500 The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum... More Details

White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". A... More Details

White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". A... More Details

Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". A... More Details

Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". A... More Details

AT-3B Small Black Nylon Wire Tie Mount - Qty. 500 The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a m... More Details

Acrylic Adhesive - 10-Pack CAN NOT SHIP AIR,UPS GROUND ONLY AT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures i... More Details

AT-5 Large White Nylon Tie Mount - Qty. 500 The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has... More Details

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull ... More Details

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull ... More Details

Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull ... More Details

Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull ... More Details

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500 The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie a... More Details

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10 Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requir... More Details

Aluminum Base Wire Tie Mount This tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with th... More Details

Aluminum Base Wire Tie Mount This tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with th... More Details

AT-850 Square Mixing Tip 4" - Case of 50 Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as th... More Details

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10 Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility o... More Details

AT-85810 Mixing Tips *10-Pack Its unique design eliminates any possibility of the cartridge plugging up as the entry is separated.  This prevents cross-contamination of the two parts, keeping the cart... More Details

Aluminum Wire Tie Used with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and s... More Details

Aluminum Wire Tie Used with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and s... More Details

Executive Adhesive & Fastener Kit w/AT-8040 Adhesive This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Con... More Details

Executive Fastener Kit - No Adhesive This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Ac... More Details

No Slide Metal/Composite Bonder *Case of 10* Revolutionary Metal Bonder will hold heavy parts at application without sliding on a vertical or overhead surface. AT-8040 will hold 3,500 lbs in 40 minute... More Details

Retail Wire Tie Kit with AT-8040 Adhesive The AT-1050 kit contains one manual mix tube of AT-8040 adhesive and 25 pieces of AT-5 white wire tie mount. Just enough parts for a small wiring job and an i... More Details

Single Clamp Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous se... More Details

Single Clamp Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous se... More Details

Single Clamp Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous se... More Details

Single Clamp Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous se... More Details

Floating Nut Plates Our floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesi... More Details

Floating Nut Plates Our floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesi... More Details

Stainless Steel Panel Stud .62" Base 8 x 32 Thread 1.25" Tall - 100 Pack Weld Mount offers wire tie mounts, hose, and cable clamps, studs, standoffs, and floating nutplates. All of the fasteners are m... More Details

Stainless Steel Panel Stud .62" Base 8 x 32 Thread 1.5" Tall - 100 Pack Weld Mount offers wire tie mounts, hose, and cable clamps, studs, standoffs, and floating nutplates. All of the fasteners are mo... More Details

Stainless Steel Panel Stud .62" Base 8 x 32 Thread 1" Tall - 100 Pack Weld Mount offers wire tie mounts, hose, and cable clamps, studs, standoffs, and floating nutplates. All of the fasteners are moun... More Details

Stainless Steel Standoff 1.25" Base 1/4" x 20 Thread .75" Tall - 6-Pack Unlike the SOB standoffs which have a blind thread, the SOT series standoffs have a thread which runs all the way through the ba... More Details

Stainless Steel Stud 1.25" Base 1/4 x 20 Thread 0.75" Tall - 100 Pack Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile stren... More Details

Stainless Steel Stud 1.25" Base 10 x 24 Threads .50" Tall - 15 Quantity Studs with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that ... More Details

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 Quantity Studs with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that... More Details

17" Rail Mount Flag Pole - 1/2" Diameter, Stainless Steel Staff Nylon Mount Features: Rail Mount Flagstaff 304 S.S. staff and Black Nylon Bracket Diameter - 1/2" Length - 17" Bracket - 7/8" and 1" tub... More Details

Clamp-On Flag Pole - 1/2" Diameter Stainless Steel Clamp & Pole Features: Clamp-On Flagstaff Pole made of 304 S.S. Clamp made of 316 S.S. Diameter - 1/2, Length - 17", Clamp Tube Size-7/8" Product Spe... More Details

Key with tools and bottle opener. Material: 304 Stainless Steel Dimensions: L: 3-7/8" W: 2-3/4" Product Specifications Dimensions4" L × 3" W × 1" HShipping Weight0.15 lbCountry of OriginTWHarmonized C... More Details

Director's Chair with Black Cushion - Teak Features: Teak Director's Chair with Cushion Seat Covers Chair with Black Seat Cushion Stainless steel hardware 18" high from floor to seat Folds for easy st... More Details

Extra Large Stainless Steel Flush Cupholder  Features: Longer depth fits larger water bottles and can coolers (including Yeti) Flush mount design Drink pad made with UV-resistant vinyl for longer life... More Details

Flush Drinkholder Cut-Out: 3-7/8" Outer Diameter: 4-3/8" Depth: 2-1/4" - 3-1/8" Material: 304 Stainless Steel Includes mounting gasket, pad & 3/8" drain tube Fits cans, bottles & can coolers Product S... More Details

Flush Mount Cup Holder w/Blue LED Light - Stainless Steel LED Illuminated Flush Cup holder with Blue light Cut-Out: 3-3/4" O.D.: 4-1/4" Uses 12V battery power Comes with 6" wire leads Includes Thick M... More Details

Flush Mount Cup Holder w/Red LED Light - Stainless Steel LED Illuminated Flush Cup holder with Red light Cut-Out: 3-3/4" O.D.: 4-1/4" Uses 12V battery power Comes with 6" wire leads Includes Thick Mou... More Details

Flush Mount Flag Pole Socket - Stainless Steel - 1-1/4" ID Features: 316 S.S. Flush Mounted Flagpole Socket. Tube inside dia - 1-1/4" Base 2-3/4" Height - 2-9/16" Fastener - #12 (3) Product Specificat... More Details

Folding Drink Holder - Black Nylon Black Nylon 3-3/4" x 3-3/4" Fastener Included Product Specifications Dimensions5" L × 5" W × 1" HShipping Weight0.2 lbCountry of OriginTWHarmonized Code7326.90.8588 More Details

Folding Drink Holder - White Nylon White Nylon 3-3/4" x 3-3/4" Fastener Included Product Specifications Dimensions5" L × 5" W × 1" HShipping Weight0.2 lbCountry of OriginTAIWANHarmonized Code7326.90.8... More Details

Large Stainless Steel Cupholder (Fits YETI) Features: Wider mouth fits larger water bottles and can coolers (including Most Yeti Sizes) Drink pad made with UV-resistant vinyl for longer life Drink pad... More Details

Mooring Bit Height: 3" Diameter:2-3/8" Cross Piece: 7" Base: 3-3/4" x 4-1/2" Fastener:5/16" Product Specifications Dimensions8" L × 5" W × 4" HShipping Weight1.8 lbCountry of OriginTWHarmonized Code73... More Details

Premium Golden Teak Oil - 16oz Features: Premium Golden Teak Oil 16oz. Preserves, seals, and provides a protective finish to teak wood Penetrates deep into the teak for ultimate protection Dries quick... More Details

Premium Teak Brightener - 16oz Features: Premium Teak Brightener 16oz. Brightens and enhances the natural wood grain and color. Easy to use, no hard rubbing Will not harm fiberglass or painted surface... More Details

Premium Teak Cleaning - 16oz Features: Premium Teak Cleaner 16oz. Cleans weathered & stained teak without hard rubbing. Will not harm fiberglass or painted surfaces Easy to Use This product may not be... More Details

Single Engine Control for Clutch or Throttle Features: Base Size - 3" x 5-3/8" Fastener - #10(4) Features external brake tension adjust and positive travel limit stops Complete with cable mounting bra... More Details

Square Side Table - Teak Features: Teak Square Side Table Solid teak construction Slat tabletop design Can be used indoors or outdoors Size: 20” SQ. x 18” H Assembly: Some assembly required Finish: Oi... More Details

Teak Flag Pole - 18" - 3/4" Base Diameter Features: Teak Flag Pole 18" Length 3/4" Base Diameter Hardware not included Traditional ball cap style flag pole Product Specifications Dimensions18" L × 3" ... More Details

Teak Flag Pole - 24" - 1" Base Diameter Features: Teak Flag Pole 24" Length 1" Base Diameter Hardware not included Traditional ball cap style flag pole Product Specifications Dimensions25" L × 3" W × ... More Details

Teak Flag Pole - 30" - 1" Base Diameter Features: Teak Flag Pole 30" Length 1" Base Diameter Hardware not included Traditional ball cap style flag pole Product Specifications Dimensions30" L × 2" W × ... More Details

Teak Flag Pole - 36" - 1-1/4" Base Diameter Features: Teak Flag Pole 36" Length 1-1/4" Base Diameter Hardware not included Traditional ball cap style flag pole Product Specifications Dimensions36" L ×... More Details

Teak Flag Pole - 48" - 1-1/4" Base Diameter Features: Teak Flag Pole 48" Length 1-1/4" Base Diameter Hardware not included Traditional ball cap style flag pole Product Specifications Dimensions49" L ×... More Details

Top Mount Flag Pole Socket - 1" ID - Polished Brass Features: Polished Brass Top Mounted Flag Pole Socket Tube I.D. - 1" Base - 2-1/2" Height - 2" Fastener - #6 (3) Product Specifications Dimensions6"... More Details

Top Mount Flag Pole Socket 1-1/4" ID - Polished Brass Features: Polished Brass Top Mounted Flag Pole Socket Tube I.D. - 1-1/4" Base - 2-3/4" Height - 2-1/8" Fastener - #6 (3) Product Specifications Di... More Details

Top Mount Ring SS Cup Holder - 1-Drink - Base Mount Top mount drink holders are great for console and table tops. Our top mount drink holder allows for 1/4" wood screw or bolt to fasten to the console... More Details

Top Mount Ring SS Cup Holder - 2-Drink - Base Mount Top mount drink holders are great for console and table tops. Our top mount drink holder allows for 1/4" wood screw or bolt to fasten to the console... More Details

Top Mount Ring SS Cup Holder - 3-Drink - Stud Mount Top mount drink holders are great for console and table tops. Our stud mount cup holders allow for blind fastening for a neat look on the top of the... More Details

Top Mount Ring SS Cup Holder - 4-Drink - Stud Mount Top mount drink holders are great for console and table tops. Our stud mount cup holders allow for blind fastening for a neat look on the top of the... More Details

Top-Mounted Flag Pole Socket - CP/Brass - 1-1/4" ID Features: CP/Brass Top Mounted Flag Pole Socket Tube I.D. - 1-1/4" Base - 2-3/4" Height - 2-1/8" Fastener - #6(3) Product Specifications Dimensions3... More Details

Top-Mounted Flag Pole Socket - Stainless Seel - 1-1/4" ID Features: 316 S.S. Top Mounted Flagpole Socket. Inside Tube Dia. - 1-1/4" Base - 2-3/4" Height - 2-1/4" Fastener - #10 (3) Comes with 1/4-28 s... More Details